You are viewing the archived version of the site.
Go to automodeler.com for the current dynamic site!
Go to automodeler.com for the current dynamic site!
1⁄35A Hell of a Way To Die
IntroductionThe subjects that I model are not really pre-planned; it’s just what takes my fancy at the time. I never had any interest in the war for the Pacific and had never modelled anything from that theatre either …. well that was until I won Dragon’s M4A2 “Tarawa” Sherman kit in a previous month’s “Dragon Model f the Month” competition. I quickly found some Internet reference material to guide me; Terry Ashley’s Review on PMMS and the “Tarawa on the Web” site. I also scored Derrick Wright’s “Tarawa, A Hell of a Way to Die” quite cheaply on E-bay, which has woken a new found interest in the Pacific theatre and especially the marines who fought there. I enjoyed this book so much, and couldn’t think of a better name for the scene, so I used the book title!
Historical BackgroundOperation Galvanic – the invasion of the Gilbert Islands by the US Marine Corps and Army units of the V Amphibious Corps, began in the early morning of 20th November 1943, with a huge naval bombardment of the tiny island of Betio on the western edge of the Tarawa atoll. It marked the beginning of America’s island-hopping advances across the Pacific, and would have ended with the invasion of the Japanese mainland if it were not for the atomic bombs dropped on Hiroshima and Nagasaki. On the 20th of November 1943, the Japanese garrison was 4,836 men. 76 hours later the survivors, 17 Japanese soldiers and 129 Korean labourers were taken as prisoners of war. 837 Marines were killed in action, 153 died later from wounds or were missing and presumed dead, and 2296 were wounded.
M4A2 Construction: Suspension and hullThe kit construction begins in step one with assembly of all the bogeys, drive wheels and idlers. There are 2 choices of drive-wheel offered with the "fancy (V30)" or the solid plate type (V31) with V31 being correct for the Tarawa version. To complete the bogey assemblies there are bolt-heads on the “V” sprue for the track guides but these are not mentioned on the instructions. A sharp scalpel was used to slice them off and they were carefully placed with pincers. Each bogey-wheel has a back insert with full detail but they are slightly smaller in diameter than the hollow receiving side and result in a visible gap, which may not be seen on the finished model, but I filled these in roughly with Mr.Surfacer 500 just in case. A quick swipe with some sand paper cleaned up the idlers. Because of reports of a poor fit with the transmission cover and the final drive covers (A13 and A14), I cemented both connecting sides and pushed them together as best I could. Extruding soft plastic appears to have filled the small gaps. I decided to leave the kit instruction-sequence at this point and join the top and bottom hull, allowing any major joining-work to be taken care off without details getting in the way. The bolted bar that sits between the top hull and the transmission cover was fixed to the top hull. This meant a pretty neat join to the top hull but some Mr.Surfacer will take care of the very little gaps when joining this assembly to the bottom hull. All of this now meant that there was a slight gap under the hull backside. I took care of this by squeezing 0.5mm plastic strip in and then cutting it back when the cement had dried, using a little Humbrol putty to tidy up the joint seems. The remaining triangle-shaped hole is where the idler mounts will be fixed. All that was left was to cut off a nib as called out on Step 6. The fixed scopes in front of the driver and machine gunner will be modelled closed, so there was no need to insert them before joining the top and bottom hull assemblies. I then went back and completed the remains of steps 2, 3 and 4 once the hull was secured.
Stowage and DetailsSteps 5, 6, 7 and 8, deal with adding the hull and stowage details in a pretty straight forward assembly with just some minor clean up. I managed to get the Military Modelling magazine issue from December 2006 which features Steve Zaloga´s build of this model, and according to Mr. Zaloga, the Tarawa Shermans did not have their headlights fitted. I had originally decided to keep mine separate to ease painting, but now could skip this altogether. I punched 2 discs from sheet styrene to act as plugs and cemented these in place. To complete the lower hull details, the front mudguards were to be added and these are included only as photo etched items. Well the day had to come .... Id been putting it off for ages .... and its been bugging me for some time ... I had to try soldering! The fenders and turret vane were soldered at the same time. Swedish Modeller Pål Björkman sent me a link to “Soldering Basics By John Robinson” which proved to be very helpful. In addition to the soldering, two neat tips I read about at this time were incorporated into the build. Tip #1 was from Dinesh Ned´s excellent Pacific Sherman, where he used some thin plastic for straps on the pioneer tools, and tip #2 was S. Zaloga´s method of attaching thin etched items to the tank using putty and marking it to look like weld seams.
TurretSteps 9 and 10, deal with the turret assembly. Again I choose to join the two halves, before adding details, so that any gaps could be eliminated. There was quite a significant gap between the top and bottom pieces, so I stretched some sprue and cemented it in place much like adding a weld seam. When dry, I removed the "weld" with a rounded blade and sanded it flat. Then more Humbrol polly cement was stippled over the whole area to re-create the cast texture. The remaining turret details presented no problems, but I used lead foil and Aber buckles instead of the stiff kit-supplied belts for the back of the turret and added a shovel from the spare box for visual interest. To finish, the etched sand-guard attachment strip was added to the sides and completed on the backside with some plastic strip, as they are not included in the kit. Painting was mostly done with Tamiya acrylics, but small details were painted using Humbrol enamels, and washes were made with oil paints. Pastels were used to give a dusty appearance, as sand would stick to a wet vehicle having just come from the water.
Copyright ©2021 by Frank Glackin. _OPINIONS Auto Modeler, KitMaker Network, or Silver Star Enterrpises. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of ModelGeek. All rights reserved. Originally published on: 2007-08-17 00:00:00. Unique Reads: 33785